Brandtech-scientific Titrette Manual de usuario Pagina 64
- Pagina / 164
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
64
Problem Possible cause Corrective action
Troubleshooting
Liquid is above the piston Piston leaks Perform a cleaning, replace the
piston/cylinder assembly
(see page 56).
Piston difficult to move Piston/cylinder assembly is
contaminated or damaged by
crystalline deposits
Perform a cleaning, replace
the piston/cylinder assembly, if
necessary (see page 56).
Filling not possible Filling valve stuck Clean the filling valve. If the
valve ball is stuck use a 200 µl
plastic pipette tip to loosen it
(see page 60).
Filling not possible /
liquid is drawn back into the
titrating tube during filling
The discharge valve is
contaminated or the titrating
tube has been damaged
Clean the discharge valve or
exchange the titrating tube
(see page 56).
Air bubbles in the instrument Instrument filled too quickly Fill instrument slowly
Filling tube is loose or dam-
aged
Fasten the telescoping filling
tube firmly. If necessary, cut the
tube off approx. 1 cm from the
top or replace it.
Filling valve is loose or the
seal possibly has not been
inserted
Check whether the seal has been
inserted, and fasten the valve
securely with the mounting tool.
Filling tube does not dip into
the liquid
Fill up the bottle, or correctly
adjust the length of the telescop-
ing filling tube.
Recirculation tube is not
mounted or mounted
improperly
Attach the recirculation tube.
The opening must point outward
toward the bottle wall.
Titrating not possible Discharge valve stuck Clean or exchange the titrating
tube with its integrated discharge
valve (see page 56).
The volume delivered is
smaller than that indicated
The instrument has not been
completely primed
Prime the instrument again
(see page 41).
Seal might not have been
inserted or the filling valve is
loose
Check whether the seal has been
inserted, and fasten the valve
securely with the mounting tool.
Filling valve is blocked or
damaged
Clean, and if necessary replace
the filling valve (see page 60).
The instrument doesn’t
indicate any function
Internal error Perform a restart: remove the
batteries, wait 1 minute and then
replace them (see page 61).
- Titrette 1
- Inhaltsverzeichnis 3
- Sicherheitsbestimmungen 4
- Funktion und Einsatzgrenzen 4
- Bedienelemente 6
- Erste Schritte 7
- Entlüften 9
- Titrieren 10
- Pausenfunktion 11
- PC-Schnittstelle (optional) 11
- Sichtfenster tauschen 12
- Empfindliche Medien 12
- Fehlergrenzen 13
- 1. Gerät vorbereiten 14
- 2. Volumen prüfen 14
- 3. Berechnung 14
- Zusatzfunktionen 15
- Justieren 16
- Erneutes Justieren 17
- Werksjustierung 18
- Kalibriertermin einstellen 19
- Dezimalstellen ändern 21
- Reinigung 22
- Batteriewechsel 29
- * Sägezahngewinde 30
- Störung – was tun? 32
- Reparatur · Kontaktadressen 33
- Kalibrierservice 34
- Mängelhaftung 34
- Entsorgung 34
- Table of Contents 35
- Safety Instructions 36
- Operating Elements 38
- First Steps 39
- Titrating 42
- The Pause function 43
- PC interface (optional) 43
- Sensitive Media 44
- Error Limits 45
- 2. Check the volume 46
- 3. Calculation 46
- Additional Functions 47
- Adjustment 48
- Factory Default 50
- Calibration Schedule 51
- Auto Power Off 52
- 1. Bring up the dP 53
- 2. Changing the 53
- 3. Confirming 53
- Cleaning 54
- Replacing Batteries 61
- * buttress thread 62
- Troubleshooting 64
- Repairs · contact addresses 65
- Disposal 66
- Warranty 66
- Calibration Service 66
- Table des matières 67
- Règles de sécurité 68
- Français 69
- Eléments de commande 70
- Premiers pas 71
- Désaérage 73
- Titration 74
- La fonction pausa 75
- Interface PC (en option) 75
- Montage du tube de séchage 76
- (en option) 76
- Remplacement de la fenêtre 76
- Milieux sensibles 76
- Limites d'erreur 77
- 2. Contrôle du volume 78
- 3. Calcul 78
- Fonctions additionnelles 79
- Ajustage 80
- Nouvel ajustage 81
- Ajustage d'usine 82
- 1. Appel du mode 83
- 2. Entrée de 83
- 3. Confirmation de 83
- Modification des décimales 85
- Nettoyage 86
- Remplacement des piles 93
- * Filet en dent de scie 94
- Dérangement – que faire? 96
- Elimination 98
- Garantie 98
- Contenido 99
- Normas de seguridad 100
- Elementos de manejo 102
- Primeros pasos 103
- Pugar el aire 105
- Valoración 106
- Función de pausa 107
- (opcional) 108
- Medios sensibles 108
- Montaje del tubo de secado 108
- Límites de errores 109
- 1. Preparación del aparato 110
- 2. Prueba de volumen 110
- 3. Cálculo 110
- Funciones adicionales 111
- 1. Calcular el valor 112
- 2. Elegir el modo 112
- 3. Introducir el valor 112
- 4. Confirmar el valor 112
- Nuevo ajuste 113
- Ajuste de fábrica 114
- 1. Elegir el modo 115
- 2. Introducir la fecha 115
- 3. Confirmar el valor 115
- Auto-Power-Off 116
- 2. Modificar las 117
- Limpieza 118
- Cambiar las baterías 125
- * Rosca dentada 126
- ¿Qué hacer en caso de avería? 128
- Eliminación 130
- Service de calibration 130
- Garantía 130
- Indice dei contenuti 131
- Norme di sicurezza 132
- Italiano 133
- Elementi funzionali 134
- Primi passi 135
- Spurgo dell'aria 137
- Titolazione 138
- La funzione di pausa 139
- (opzionale) 140
- Liquidi sensibili 140
- Limite di errore 141
- 1. Preparare lo strumento 142
- 2. Controllare il volume 142
- 3. Calcolo 142
- Funzioni aggiuntive 143
- Calibrazione 144
- Ricalibrazione 145
- Calibrazione di fabbrica 146
- 1. Richiamare 147
- 2. Inserire il valore 147
- 3. Confermare 147
- Modifica cifre decimali 149
- Sostituzione delle batterie 157
- * Filettatura a dente di sega 158
- Smaltimento 162
- Garanzia 162
Relacionado con productos y manuales para Instrumentos de medición Brandtech-scientific Titrette
(133 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.082 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales